Description

Designing ventilation systems with the fan mounted in a skylight or a flat roof is easy. With a low profile cowl, the LoWatt T-Series roof model is suitable for installation in horizontal, angled and vertical glass and for fixing plates in roofs. For vertical windows or walls in exposed areas and single and double glazing including most types of glass up to 32mm thick. Greater thicknesses can be accommodated using extended fixing rod sets. Both sizes of Vent-Axia roof plate assemblies can be fitted easily into flat roofs.

Shutter

With energy saving in mind LoWatt T-Series models are supplied complete with an integral instantaneous automatic louvre shutter concealed behind the interior grille. It will operate on both intake and extract and at any angle of mounting.

The shutter is electronically controlled by an actuator with a damped action giving quiet operation during instant opening and closing. The interlocking edges of the shutter blades provide maximum backdraught protection.

When the ventilating unit is used with a LoWatt T-Series Controller, the shutter can be set open with the fan motor switched off to provide natural ventilation without the security risk of an open window.

Flat roof

LoWatt T-Series roof models may be installed through solid roofs using a roof plate assembly and, if required, an eggcrate grille or louvred grille in the ceiling below. Alternatively, if ventilation is from a suspended ceiling, single spigots and flexible ducting may be used to connect the unit and extract grille.

Corrugated roof

LoWatt T-Series roof models are suitable for fixing through corrugated sloped and vertical cladding using a suitable soaker flange. The soaker flange consists of a replacement sheet with a flat section to carry the unit. A suitable sealing compound should be used between the plate and the exterior unit seal.

Pitched roof

LoWatt T-Series roof models may be installed in fixing plates with zinc or lead weathering apron (provided by others), fitted directly to a tiled or slated roof to provide a water-tight installation. A suitable sealing compound should be used between the weathering apron and the exterior unit seal.

NEW LoWatt T-Series Controller

LoWatt T-Series Controllers are available in both Wired and Wire-less FM versions. The three speed push button surface mounted controllers provide intake/extract and shutter only options and auto mode position for use with external sensors.

Wired versions are connected to the fan using a plug-in Safety Extra Low Voltage 2-core signal cable supplied (10m), allowing simple and safe installation. Alternatively, the Wire-less FM controller offers full control without the need for any wiring, ideal for premises where installations need to be carried out with minimum disruption or where surface wiring can be classed as unsightly or obtrusive.

Sensors

Can be used in conjunction with a LoWatt T-Series Controller

Ambient Response Humidity Sensor - Self programming electronic On/Off wall mounted humidity sensor which reacts to any rapid increase in humidity and temperature. Night time RH increment setback feature

Ecotronic Humidity Sensor - Adjustable set point, solid state controller. Pullcord provides manual override. Adjustable from 65% to 90%RH.

Air Quality Sensor - Automatically reacts to the depletion of air quality, sensing tobacco smoke, smells and toilet odours to regulate mechanically ventilated areas

Performance

Unit Size		LoWatt TX9RF Wireless	LoWatt TX9RF
Stock Ref. No.		45 61 72	45 61 68
Amps @ 240V		0.34	0.34
Extract  Performance  m³/h	Low	313	313
	Med	526	526
	High	693	693
Watts (high)		29	29
dB(A) (med) @ 3m		40	40

Unit Size		LoWatt TX12RF Wireless	LoWatt TX12RF
Stock Ref. No.		45 61 80	45 61 76
Amps @ 240V		0.69	0.69
Extract  Performance  m³/h	Low	518	518
	Med	1017	1017
	High	1194	1194
Watts (high)		67	67
dB(A) (med) @ 3m		48	48

Recommended controller:
Wire-less Controller Stock Ref. No. 45 58 74
Wired Stock Ref. No. 45 58 73

Dimensions (mm)