KAIR 150MM / 6 INCH 45 DEGREE ROUND DUCTING ELBOW BEND JOINT - SYS-150 - DUCVKC361
White Plastic 45 Degree Elbow Bend Connection - Male Spigot will fit inside Kair 150mm Round Pipe (Part: "DUCVKC670") or 152mm Flexible Hose (Part: "DUCP0092/152/35").
Easy to install and durable, just push-fit duct and fittings together. Will join any round female part of the Kair System 150 range. Also fits other ranges. Built to last out of high-quality white Polystyrene/Polypropylene plastic Material. Max / Min Temperature: +60c / -15c.
Kair plastic ducting is lightweight, durable and suitable for commercial and domestic use. It is perfectly suited for ducting your Tumble Dryer, Bathroom or Kitchen extractor fan, Hydroponics, In-Line Extract Fans, or Cooker Hood. It can be used as a part of a long ductwork run for a variety of purposes including whole-house ventilation, passive stack vent, positive input, air conditioning, HVAC, and Heat Recovery Systems.
Round rigid ducting provides superior airflow performance vs. comparative size rectangular or flexible duct. Suitable to use in compliance with Part F Building Regulations.
Genuine Kair Product & covered by the Kair 100% Satisfaction Guarantee for your peace of mind. Search for "Kair SYS-150" for the full range of Kair 180mm x 95mm Rectangular and 150mm Round fittings, outlets, and grilles. If you have any questions please do not hesitate to ask fellow purchasers via the Customer Questions & Answers system below.
Product Category | Bends |
Round System (mm) | 150 |
Product Type | Bend |
Product Group | Plastic Ducting |
Packaged Weight (Kg) | 0.18 |
Packaged Length (mm) | 160 |
Packaged Width (mm) | 190 |
Packaged Height (mm) | 190 |
Temp Max (°C) | 60 |
Temp Min (°C) | -15 |
Barcode | 5060272547097 |
Barcode - Type | EAN |
Manufacturer Product Code | DUCVKC361 |
Quick Search: | QS38802 |
Your question will be sent to a member of our team. We'll email you the answer and post it on this page. If your question is about an order you already placed, please use our Contact Form to reach the customer service team.
I am looking for parts to form a 150mm duct that passes through a tiled pitched roof. The installation diagrams I have show the fan duct fed into the roof vent via some kind of elbow, but also some other element at the bottom of the vertical stack that passes through the roof. Would that be some form of condensate trap or just a blanking plug and do you have parts to form such a vent system?
Good Morning Peter
if I were to put two offsets together what would the distance of the center line of the two straight pipes be? Same question what is the minimum distance that two offsets would achieve? Please could you answer to same question for the 125 mm pipe as well
Good morning Clive.
Customers who bought this product also purchased |
Ducting System | Actual dimensions (mm) | Space requirements (mm) | Airflow mm² |
For 4" (100mm) extractor fans or for low power cooker hoods up to 250m³/hour | |||
---|---|---|---|
System 100 - Round | 100 | 106 | 7,854 |
System 100 - Rectangular | 110 x 54 | 116 x 60 | 5,940 |
For medium extraction rates or if available depth is limited up to 500m³/hour | |||
System 125 - Round | 125 | 131 | 12,272 |
System 125 - Rectangular | 150 x 70 | 156 x 76 | 10,500 |
For 6" (150mm) extractor fans or for high power cooker hoods up to 500m³/hour & above | |||
Megaduct 220 - Rectangular | 220 x 90 | 227 x 97 | 17,968 |
System 204 - Rectangular | 204 x 60 | 210 x 66 | 12,240 |
System 150 - Round | 150 | 156 | 17,671 |
System 150 - Rectangular | 180 x 90 | 186 x 96 | 16,200 |
For a shallow space, such as ceiling voids or under floor, where high extraction rates are not needed: | |||
System 300 - Rectangular | 308 x 29 | 314 x 35 | 8,932 |
System 225 - Rectangular | 234 x 29 | 240 x 35 | 6,786 |
System 100 Round/Rectangle | System 125 Round/Rectangle | System 150 Round/Rectangle | System 204 | System 225 |
System 220 | System 300 | |||
Actual Dimensions (mm) Space Requirements (mm) |