A water heating battery is for heating air in ventilation systems with circular ducts.
Aluzinc-coated casing, heat transmission element with copper tubes and aluminium fins.
Removable cover for cleaning the unit.
The water-heating battery can be installed in a horizontal or a vertical duct with optional direction of airflow.
Max operating temperature 150 °C
Max operating pressure 1,6 MPa (16Bar)
When connecting a heater to the water system, the following things should be considered:
1. The heater must be connected with clamping ring connectors.
2. The connecting pipes from the heat exchanger must under no circumstances be subjected to twisting or bending stresses when assembling the pipe connectors etc. Use suitable tools to counteract the twisting/bending moments during assembly.
3. Ensure that forces due to expansion in the system and the intrinsic weight of the piping system itself do not put loads on to the heat exchanger.
4. The water inlet should normally be connected to the lowest pipe connector in order to facilitate venting of the heat exchanger. A venting valve should normally be installed near the heat exchanger or at the highest point in the system.
5. The heater must be connected in such a way that the system is easy to empty in the event of repair work, a longer operational stop, or when there is a risk of freezing, etc.
6. Immediately after the system has been filled with water, the duct heater and its connections must be checked for water leaks. Leaks can cause water damage.
Max. operating temperature: 150°C
Max. operating pressure: 1,6 MPa (16 Bar)
WARNING!! If the water in the heat exchanger freezes, then it can burst, if this is the case water may leak from the system and cause water damage.If there is a risk of frost the heater must be installed with a circulation pump in a secondary circuit to ensure that a constant flow is achieved in the heater.
A frost protection thermostat or regulator with automatic frost protection must also be installed to shutoff the fans and outside air damper in the system, and possibly switch on an alarm.
The heat exchanger must be cleaned regularly in order to retain the best performance from the heater. The cleaning interval depends entirely on the cleanliness of the air and how the filter and remainder of the system are maintained.
The heat exchanger is readily accessible for cleaning when the cover on the heater is removed. First, the air entry side of the heat exchanger is cleaned with a brush and then the whole heat exchanger can be cleaned with compressed air, water or steam.
The dirt is blown or washed away in a direction away from the exit side towards the entry side. Cleaning is facilitated by using a mild detergent (check first that the detergent does not have a detrimental effect on copper and aluminium).
Be careful not to damage the thin fins on the heat exchanger.
The heater is designed to be inserted into standard spiral ducting and is fixed to the ducting with screws.
The heater should not be fitted too close to a fan outlet or a bend in the ducting because then there is a risk that the air flow through the heat exchanger is uneven which can result in lower efficiency.
An effective filter is recommended in the system to reduce maintenance work. See under the heading Cleaning.
The duct heater can be fitted in a horizontal or a vertical duct with optional direction of airflow. To facilitate venting of the heat exchanger, the unit should be fitted with the longitudinal tubes horizontal. The heater is normally fitted after the fan. However it can be fitted before the fan, but then a check must be made that the fan motor and other components are approved for the elevated temperature after the heater.
|Made to order||Yes|
|Round System (mm)||125|
|Product Type||Water Heating Battery|
|Economy Delivery||Not Eligible|
|Next Day Delivery||Not Eligible|
Last Orders for delivery before Christmas
Please call us on 020 8463 9696 or place orders online by midday Thursday 20th December 2018.
Will be limited only to online queries, please allow up to 48 hours for a response.
All orders are subject to availability. Please call us on 020 8463 9696 to check availability or likely despatch date.
View full delivery dates here
SIDCUP SHOWROOM STORE (Get Directions)
Closes: 4:30pm Thirsday 20th December.
Opens: 8:00am Wednesday 2nd January 2019
|Shipping Method||Under £100*||Over £100*|
4 to 7 Days (Orders under £25 inc VAT)
4 to 7 Days (Orders over £25 inc VAT)
2 to 4 Days (Interlink or TNT)
Next Working Day Delivery+
* Usually £200+vat
+ Order before noon for Next Working Day Delivery for items in stock
Excludes Highlands, Islands, and Certain Postcodes.
Please Note: Ducting tubes over 200mm in diameter and 3 metres in length may incur additional shipping charges.
See the full delivery information here: Full delivery information
Your question will be sent to a member of our team. We'll email you the answer and post it on this page. If your question is about an order you already placed, please use our Contact Form to reach the customer service team.
|Customers who bought this product also purchased|
|Ducting System||Actual dimensions (mm)||Space requirements (mm)||Airflow mm²|
For 4" (100mm) extractor fans or for low power cooker hoods up to 250m³/hour
|System 100 - Round||100||106||7,854|
|System 100 - Rectangular||110 x 54||116 x 60||5,940|
For medium extraction rates or if available depth is limited up to 500m³/hour
|System 125 - Round||125||131||12,272|
|System 125 - Rectangular||150 x 70||156 x 76||10,500|
For 6" (150mm) extractor fans or for high power cooker hoods up to 500m³/hour & above
|Megaduct 220 - Rectangular||220 x 90||227 x 97||17,968|
|System 204 - Rectangular||204 x 60||210 x 66||12,240|
|System 150 - Round||150||156||17,671|
|System 150 - Rectangular||180 x 90||186 x 96||16,200|
For a shallow space, such as ceiling voids or under floor, where high extraction rates are not needed:
|System 300 - Rectangular||308 x 29||314 x 35||8,932|
|System 225 - Rectangular||234 x 29||240 x 35||6,786|
| System 100 |
| System 125|
| System 150|
|System 204||System 225|
|System 220||System 300|
|Actual Dimensions (mm) Space Requirements (mm)|