Kair cowled vent with damper flap & 100mm round spigot. Designed for use with 100mm round ducting.
Cowl protects against driving rain and gusts of wind entering your property via the duct run.
Damper flap can be closed to help reduce unpleasant odours, noises, or draughts flowing back through your duct.
4 inch / 100mm round male spigot on the back of the grille fits inside most comparable size pipes/hoses such as Kair 100mm Round Female Duct Pipe (Part: "DUCVKC250") or 102mm flexible hose (Part: "DUCP002/102/35").
Perfectly suited for ducting your bathroom or kitchen extractor fan, hydroponics, in-line extract fans, tumble dryer, or a cooker hood.
This item can be used as a part of a long ductwork run for a variety of purposes including whole-house ventilation, passive stack vent, positive input ventilation, air conditioning, HVAC, and Heat Recovery systems.
Kair SYS-100 plastic rigid ducting is perfect for DIY and Trade use and provides superior airflow performance and durability versus flexible duct.
Suitable to use in compliance with Part F Building Regulations.
Genuine Kair Product & covered by the Kair 100% Satisfaction Guarantee.
PLEASE NOTE: The cowl comes from the manufacturer with 'slightly bent' sides. This is to enable easy removal of cowl initially so that backplate can be screwed to the wall. Once secured the cowl can be fitted into the backplate and sides pushed so that the sidewall clamps click into the backplate.
Stainless steel versions are also available in 100mm, 125mm, and 150mm versions. Click here to view the Kair Stainless Steel Cowled Outlet range.
Versions with 110mm x 54mm rectangular spigots are also available. Click here to view the full range of Kair Plastic Cowled Wall Outlets
Looking for compatible products?
Compatible with the extensive Kair SYS-100 range of fittings, outlets, and grilles.
|Round System (mm)||100|
|Product Type||Grille - Cowl|
|Product Group||Plastic Ducting|
|Spigot size (mm)||37 x 96 x 96|
|Packaged Weight (Kg)||0.139|
|Packaged Length (mm)||100|
|Packaged Width (mm)||155|
|Packaged Height (mm)||155|
|Temp Max (°C)||60|
|Temp Min (°C)||-15|
|Polypipe / Domus (similar)||4902|
|Pressure Loss (Pa) 15 l/s||4.72|
|Pressure Loss (Pa) 30 l/s||17.18|
|Pressure Loss (Pa) 60 l/s||62.48|
Your question will be sent to a member of our team. We'll email you the answer and post it on this page. If your question is about an order you already placed, please use our Contact Form to reach the customer service team.
I have received this product the sides are con caved and the inner disc is stuck It doesn't seem to be correct ? Please advise
Thank you for your enquiry,
|Customers who bought this product also purchased|
|Ducting System||Actual dimensions (mm)||Space requirements (mm)||Airflow mm²|
For 4" (100mm) extractor fans or for low power cooker hoods up to 250m³/hour
|System 100 - Round||100||106||7,854|
|System 100 - Rectangular||110 x 54||116 x 60||5,940|
For medium extraction rates or if available depth is limited up to 500m³/hour
|System 125 - Round||125||131||12,272|
|System 125 - Rectangular||150 x 70||156 x 76||10,500|
For 6" (150mm) extractor fans or for high power cooker hoods up to 500m³/hour & above
|Megaduct 220 - Rectangular||220 x 90||227 x 97||17,968|
|System 204 - Rectangular||204 x 60||210 x 66||12,240|
|System 150 - Round||150||156||17,671|
|System 150 - Rectangular||180 x 90||186 x 96||16,200|
For a shallow space, such as ceiling voids or under floor, where high extraction rates are not needed:
|System 300 - Rectangular||308 x 29||314 x 35||8,932|
|System 225 - Rectangular||234 x 29||240 x 35||6,786|
| System 100 |
| System 125|
| System 150|
|System 204||System 225|
|System 220||System 300|
|Actual Dimensions (mm) Space Requirements (mm)|