Sale
Galvanised Bend – 90 Degree Pressed
Standard:
- Standard version is supplied without “safe” rubber seal push fit seals.
- Installation may need sealant or solvents.
Rubber Seal:
- The i-sells safe system is a quickly assembled solution based on a double-lipped, factory-installed seal made from EPDM rubber.
- Fast and easy to install: Allows installation without sealant or solvents.
- Saves money and time on extra installation steps – Can be twisted and adjusted with tightness unaffected.
SKU: GALB90100 QS Code: QS8064 
| |
| Dimensions (mm) | WHL 100200200 |
|---|---|
| Temperature (°C) | Max 250 |
| Material | Galvanised Steel |
| View All Technical Details | |
PDF Files
Similar Products
Metal Ducting Pressed 90 degree bend.
Galvanised steel bend with male spigots – Fits inside our range of galvanised spiral and other female coupling products. Our fittings are produced in accordance with DW144, and have a rolled edge for safer handling and improved alignment.
Standard:
- Standard version is supplied without “safe” rubber seal push fit seals.
- Installation may need sealant or solvents.
Rubber Seal:
- The i-sells safe system is a quickly assembled solution based on a double-lipped, factory-installed seal made from EPDM rubber.
- Fast and easy to install: Allows installation without sealant or solvents.
- Saves money and time on extra installation steps – Can be twisted and adjusted with tightness unaffected.
6 reviews for Galvanised Bend – 90 Degree Pressed
You must be logged in to post a review.
Questions and answers of the customers
-
The listing says Fittings should be secured using the appropriate fixing method, what are they?
-
QThe listing says Fittings should be secured using the appropriate fixing method, what are they?answer nowA Hello MatthewThank you for your question. To secure the bend to the ducting you will either rivet or screw it together and seal the outside joint with some aluminium tape. If you have any further questions please do not hesitate to come back to meKind RegardsAnita
Can a safe pressed bend be used to connect to a direct air feed on a multi fuel stove?
-
A Good morning Keith. Probably not, as the seal have a maximum temperature rating of 30 degree constant or 50 degrees intermittent.The bend itself has a temperature rating of 200 degrees constant and 250 degrees intermittent.Kind regards, Marc
Want to use this to vent cooker hood, what is the difference between using the safe pressed product compared to pressed bend product?
-
QWant to use this to vent cooker hood, what is the difference between using the safe pressed product compared to pressed bend product?answer nowA Good morning Terry. The safe version has the addition of a rubber seal which means you dont need to use sealant. Its probably better for a small project.Kind regards, Marc.
Need 3 no. 225 diam x 90 pressed bends
Can you help??
-
A Hello TonyThank you for your question. Do you have plastic or metal ducting? if you have metal then this item would have to be fabricated and would require a drawing and exact dimensions of what is required as this item would not be refunded and is nonreturnable. If I can help any further please do not hesitate to contact meKind RegardsAnita
Hi, if i buy the QS2831 semi ridgid ducting will this galvanised bend fit either end?
-
A Hi Mike The quick answer is yes!The spigots/connections on the bend are male fittings and straight pipe, whether flexible or rigid has female ends. You may need to tape or use a worm drive clip to secure the connection.
Hello there, do you offer something similar to this product but in an elongated circular shape? Dimensions of the 2D surface will be 140mmx240mm. Many thanks
-
QHello there, do you offer something similar to this product but in an elongated circular shape? Dimensions of the 2D surface will be 140mmx240mm. Many thanksanswer nowA Hello JessicaThank you for your question. If you could provide a drawing with the measurements i can ask our fabricator if this is something they could do. My e-mail address is [email protected] RegardsAnita
Hello,
If we were to buy a cooker extractor similar to the one on this link.
https://www.johnlewis.com/bosch-serie-2-dwp64bc50b-pyramid-chimney-cooker-hood-stainless-steel/p3535603
Could we attach rigid ducting/or this galvanised bend (depending on the height needed to take it over the kitchen cabinets) straight to the 150mm ducting circle at the top of the extractor and do away with any square metal chimney ducting? Hope that makes sense? What else would we need to do this and extract to an outside wall?
Thanks for your time
-
QHello, If we were to buy a cooker extractor similar to the one on this link. https://www.johnlewis.com/bosch-serie-2-dwp64bc50b-pyramid-chimney-cooker-hood-stainless-steel/p3535603 Could we attach rigid ducting/or this galvanised bend (depending on the height needed to take it over the kitchen cabinets) straight to the 150mm ducting circle at the top of the extractor and do away with any square metal chimney ducting? Hope that makes sense? What else would we need to do this and extract to an outside wall? Thanks for your timeanswer nowA Hello StaceyThank you for your question. You can fit the 150mm rigid ducting straight onto the spigot on the cooker hood, or if you want to fit the 150mm bend straight onto the cooker hood then a 150mm female sleeve or a piece of 150mm pipe would be required. You would need to know how many meters of 150mm ducting you need to go to the outside wall and you would require a 150mm grille for the outside. If I can help any further please do not hesitate to contact me Kind RegardsAnita
I need to know the height of the Gal Bend 200mm 90degree pressed and if this is taller or shorter than the fabricated bend please
-
QI need to know the height of the Gal Bend 200mm 90degree pressed and if this is taller or shorter than the fabricated bend pleaseanswer nowA Hello PeterThank you for your question. The height of the bend is 333mm and is smaller than the fabricated bend. If I can help any further please do not hesitate to contact me. Kind RegardsAnita
Dear Sir, Madam,
I would like to connect this product on one side to your Manrose f125 inline duct fan and on the other side to a plywood panel. In order to fit it correctly into the plywood panel do I need a specific seal or clamp ?
Thank you
-
QDear Sir, Madam, I would like to connect this product on one side to your Manrose f125 inline duct fan and on the other side to a plywood panel. In order to fit it correctly into the plywood panel do I need a specific seal or clamp ? Thank youanswer nowA Hello MarikeThe spigot will not connect to the Manrose fan as they will both be male fittings and require a double female connector.The bend is not designed to be fixed to a panel or wall but to pass through an aperture in such and connect to something on the other side (continuation of ducting??) possibly a termination vent which would be fixed to the other side, (again using a double female connector).
Can you tell me the overall length of this part hxd
-
A Hello Steve Thank you for your question. I will send the dimensions to you on a separate e-mail. Kind Regards Anita
Will the galvanised spiral 150mm duct pipe fit snuggly into the female connector coupling joint, safe pressed or the other type?
-
QWill the galvanised spiral 150mm duct pipe fit snuggly into the female connector coupling joint, safe pressed or the other type?answer nowA Hello Mark Thank you for your question. The spiral ducting will not connect to the female coupling as the spiral is female you will require a male coupling. The safe connectors with the rubber seal will fit tightly into the pipe. The vented connectors will require fixing with either rivets or screws and seal the joints with aluminium tape. If I can help any further please do not hesitate to contact me on 0208 463 9683 Kind Regards Anita
Dear Ask a Question,
I am looking for a ducting solution to a vented tumble dryer. I have a hole through the wall for a left holed tumble dryer but the NEW ones on sale are mainly rear and so if I put another hole in the wall, the holes would collapse on each other. So I am looking for a rigid bend to place into the hole of the tumble dryer and connect with the venting kit that is in the wall.
I would be most grateful for your help. The PVC hose is useless - it degraded in less than 6 weeks of use.
-
QDear Ask a Question, I am looking for a ducting solution to a vented tumble dryer. I have a hole through the wall for a left holed tumble dryer but the NEW ones on sale are mainly rear and so if I put another hole in the wall, the holes would collapse on each other. So I am looking for a rigid bend to place into the hole of the tumble dryer and connect with the venting kit that is in the wall. I would be most grateful for your help. The PVC hose is useless - it degraded in less than 6 weeks of use.answer nowA Hello RosemaryYou have a couple of options depending on what the connections are at either end, you mention the pvc hose so a different type of flexible hose should connect the same way, therefore semi rigid aluminium may be the simplest solution as you can form a bend which will stay in shape, you can find this in the quick search bar by typing QS2831 or QS2832 depending if your machine has a 100mm or 125mm spigot.Hope this helps
Hi I am looking for rigid ducting for a Kitchen cooker hood. Slightly confused by you safe duct and duct. will Galss 150 (spiral duct) fit with Gal NP 150 (coupler) and Gal B 150 (90 Bend) ? Does spiral duct fit into these fittings? what is overall high of bend? Thanks in a dance Stephen
-
QHi I am looking for rigid ducting for a Kitchen cooker hood. Slightly confused by you safe duct and duct. will Galss 150 (spiral duct) fit with Gal NP 150 (coupler) and Gal B 150 (90 Bend) ? Does spiral duct fit into these fittings? what is overall high of bend? Thanks in a dance Stephenanswer nowA Hello StephenThank you for your question. Yes the coupler and bend will fit into the sprial duct. The difference between the safe and vent is that the safe fittings have a rubber seal that will crate a seal when fitted and then you just have to seal your joint with aluminium tape. The vent fittings have to be screwed or riveted to the sprial. The overall height of the bend is 300mm If i can help any further please do not hesitate to contact me on 0208 463 9683Kind RegardsAnita
can you supply a 355 galvanised bend 90 degree
-
A Hello Brian, We are able to supply a 355mm Fabricated Galvanised Bend. The construction of our fabricated bends differs slightly from our pressed bends.These can be viewed hereKind regards, Michael
Hi. can you supply a 90deg junction that is not a swept bend. IE a piece of pipe cut and joined at 45deg.
-
QHi. can you supply a 90deg junction that is not a swept bend. IE a piece of pipe cut and joined at 45deg.answer nowA Hello Nigel Thank you for your question. Unfortunately we only sell the bends and pipe separately. We do sell flexible bends but these come with a rectangular connection.
Andrew (Trustpilot) (verified owner) –
ordered Monday delivered on Tuesday, great! (GALB90125 – Galvanised Bend – 90 Degree Pressed – 125mm, Standard)
Richard Byrne (verified owner) –
Lightweight, very robust, perfect fit, excellent double seal. I cannot think of any way to rate this less than perfect for my job. And delivery / price were superb
Philip Taylor (verified owner) –
fantastic came on time and good price
Trevor Mant (verified owner) –
all acceptable
Ian Rudge (verified owner) –
Quality product that arrived on time
Martin Horn (verified owner) –
The site is easy and quick to navigate.