Airflow iCONstant T 100mm Continuous Running DC Bathroom Fan with Timer (72687117)
-
DETAILS
Airflow iCONstant T 100mm Continuous Running DC Bathroom Extractor Fan with Timer
Application
iCONstant dMEV fans can be used in any of the wet rooms. The required trickle rate is selected by the installer when the fan is fitted – this is dependent on the application – for toilets select 6l/sec, en-suites, bathrooms and utility rooms select 8 l/sec and kitchens it is 13 l/sec. The boost will be the next speed level up with a maximum of 20 l/sec.
Model Range:
There are two iCONstant models available. On the Timer version, the boost speed is set to run on for between 2, 15, 30 or 45 minutes. With the Humidity Timer version, the intelligent humidity sensor will activate the boost speed when a set point is reached - and this can be adjusted between 60% and 90%. When the set point is reached after the boost speed kicks in, the fan will revert to the trickle speed once again.
Main Features
- Continuous running axial fan
- Selectable trickle speeds 6/ 8/ 13 l/sec
- Boost speed 8/ 13 l/sec with maximum of 20 l/sec
- Unique setup diagnostic LED light
- Very quiet running fan - from 10 dB(A)
- 24V DC Motor - economical to operate - from 1.07 watts on trickle speed of 6 l/sec
- Costs less than a low energy light bulb to run
- Flow sensor ensures the fan maintains a constant extraction rate under all conditions
- IPX5 rating - install in Zone 1 and 2
- Ideal for New Build and Refurbishments
- Complies with Building Regulations
- SAP Appendix Q eligible
- Stylish circular design suitable for wall and ceiling mounting
- 3-year warranty
-
FEATURES
Features
- Continuous running axial fan
- Unique setup diagnostic LED light
- Very quiet running fan - from 10 dB(A)
- 24V DC Motor - economical to operate
- 3 Year warranty & SAP Appendix Q eligible
-
TECHNICAL
Technical Specifications
Timer Yes Humidistat NO Pullcord YES Continuous Running YES Smart Control YES SELV YES Product Category Extractor Fan Round System (mm) 100 Product Type Axial Fan Product Group Ventilation Fan Length (mm) 120 Width (mm) 197 Height (mm) 197 Spigot size (mm) 100 Voltage (V) 100/240 IP Rating IPX5 Amps @ 240V 3 Power Min (Watts) 1.7 Power Max (Watts) 2.9 Decibel Rating (dB) - Low 10 Decibel Rating (dB) - Max 38 Colour White Weight (Kg) 0.55 Barcode 5019009318288 Barcode - Type EAN Manufacturer Product Code 72687117 Airflow Performance (l/s) - Low 6 Airflow Performance (l/s) - Med 13 Airflow Performance (l/s) - High 20 Airflow Performance (m³/h) - Low 22 Airflow Performance (m³/h) - Med 47 Airflow Performance (m³/h) - High 72 SAP Appendix Q applicable YES Warranty (Years) 3 Quick Search: QS38727 -
REVIEWS
-
Q & A
Product Questions
Questions and Answers, do you need more information about this product?
Ask a QuestionYour question will be sent to a member of our team. We'll email you the answer and post it on this page. If your question is about an order you already placed, please use our Contact Form to reach the customer service team.
#1Icon blades stickingHello, When I try to change the cover of this fan, the blades sometimes get stuck either half-open or half closed which means I can't change the cover. How do I fix this?
Question by Christopher Walker, 10-05-2021Hello,Please follow this step by step process which should resolve this issue for you.1. After the next time the fan is used and has been on for at least 5 minutes. When it turns off, turn all the power off to the fan.2. Remove the front cover, immediately. When the cover is removed the iris fins should close automatically.3. Once the cover is removed (and power switched off), please place a straight edge across the ceiling/wall to ensure the surfaces are level / straight. (i.e. no bow in wall / ceiling). Please also put a level across the fan to check that is has been installed level, on a flat surface.4. Wash the cover in warm soapy water, activating the iris whilst submerged. The fan and electronics must not be washed/ submerged in water.5. Once dry where the iris fins are, spray a little furniture polish also apply some to the rear where there are moving parts. Then using the lever on the back open the iris and let it close on its own, repeat this a few times. Remove excess polish from the front of the cover.6. Leave the fan with the cover and power off for a good twenty minutes.7. Reattach the cover. Please ensure the cover is correctly aligned to the fan and refer to the attached guide.Hope that helps.Replied by i-sells, 10-05-2021#2Timer and pull cordDear Sirs, Is the unit available with a remote switch (Light switch) for boost? Airflow states the minimum run-on time is 2 minutes. You note the minimum as 15 minutes?
Question by Peter Woodfford, 07-11-2022Good morning Peter. If the fan is wired up to the lighting circuit, then, yes it can be boosted via the light switch or the pull cord. The literature that we have on our website is incorrect, and you are quite right. The minimum over run is 2 minutes, then 15,30,45.
We are currently showing 3 of these in stock in our showroom.Kind regards,MarcReplied by i-sells, 08-11-2022 -
DELIVERY
Delivery: You'll receive in: Cost Min Order Free Delivery 3 to 5 Days FREE £100 Standard 2 to 4 Days £4.99 - Express Courier Next day+ £9.95 Any View Full Delivery Info
FREE Delivery for orders over £100 inc VAT.
+ Order before noon for Next Working Day Delivery for items in stock
Excludes Highlands, Islands, and Certain Postcodes.
Please Note: Ducting tubes over 200mm in diameter and 3 metres in length may incur additional shipping charges.
You may also like
-
List Price: £242.89
Only: £125.42 -
List Price: £143.11
Only: £67.21 -
List Price: £346.78
Only: £83.94 -
List Price: £252.38
Only: £130.33 -
List Price: £197.86
Only: £102.18 -
List Price: £221.84
Only: £161.99