Sale
Kair Cowled Outlet Grille With Round Rear Spigot and Backdraught Shutter
Similar Products
KAIR COWLED VENT COVER ROUND SPIGOT
Kair cowled vent with damper flap and round spigot. Designed for use with round ducting.
Cowl protects against driving rain and gusts of wind entering your property via the duct run.
Damper flap can be closed to help reduce unpleasant odours, noises, or draughts flowing back through your duct.
- Wipe-clean durable design for indoor or outdoor use.
- Suitable to use in compliance with Part F Building Regulations.
- Airflow performance independently tested by BSRIA or BRE.
- Built to last out of high-quality Polystyrene/Polypropylene plastic material.
- Easy to install and durable, just push-fit duct and fittings together.
- For permanent fixings, seal joints with silicone sealant or tape.
- Max / Min Temperature: +60c / -15c.
Perfectly suited for ducting your bathroom or kitchen extractor fan, hydroponics, in-line extract fans, tumble dryer, or a cooker hood.
This item can be used as a part of a long ductwork run for a variety of purposes including whole-house ventilation, passive stack vent, positive input ventilation, air conditioning, HVAC, and Heat Recovery systems.
PLEASE NOTE: The cowl comes from the manufacturer with ‘slightly bent’ sides. This is to enable easy removal of cowl initially so that backplate can be screwed to the wall. Once secured the cowl can be fitted into the backplate and sides pushed so that the sidewall clamps click into the backplate.
22 reviews for Kair Cowled Outlet Grille With Round Rear Spigot and Backdraught Shutter
You must be logged in to post a review.
Questions and answers of the customers
-
Fixing hole dimensions please. My current vent is 100 x 110 and I would like to use the existing hole positions.
-
QFixing hole dimensions please. My current vent is 100 x 110 and I would like to use the existing hole positions.answer nowA
Hi Dave, thank you for your enquiry.
If you would like to use the existing hole positions, I would suggest using a wall plate for round ducting. Use to cover areas where ducting passes through walls or other solid surfaces. Can be used to cover existing holes.
Kind regards,
Can this be fitted over an existing vent to stop the rain blowing in ?
-
A Good morning, No it cant, as it has a spigot on the rear of it to go inside 100mm ducting. If you have a louvred grill and need a cowl to go over it to give a bit of wind protection, then take a look at RYTABC8BS.Kind regards, Marc
Please advise outside dimensions of the cowl
Thankyou in anticipation
-
A Hi IanI will send you the dimensions on a separate e-mailKind RegardsAnita
Is the 6 inch of this product (DUCVKC280-BR)
the duct size?
Thank you,
cees van Dorland
-
QIs the 6 inch of this product (DUCVKC280-BR) the duct size? Thank you, cees van Dorlandanswer nowA Hello CeesThank you for your question. Yes the 6 is the duct size and will fit inside the 6 pipe. If I can help any further please do not hesitate to contact meKind RegardsAnita
Can this product be used to vent a tumble dryer?
-
A Hi Christine. You would probably be better off with a louvred grille - VKC275-BR. as the damper flap may cause a bit of air resistance and may not ventilate properly.Kind regards, Marc.
I understand the spigot fits a 125mm hose. Can I confirm the full square size of the cover. Thanks
-
QI understand the spigot fits a 125mm hose. Can I confirm the full square size of the cover. Thanksanswer nowA Hello MattThank you for your question. The full square measurements are 155mmx155mm Kind RegardsAnita
Hi, what is the length of the spigot end? my wall is 100mm and the vent-axia is 8mm.Thanks
-
QHi, what is the length of the spigot end? my wall is 100mm and the vent-axia is 8mm.Thanksanswer nowA Hello BarryThank you for your question. This grille comes in 4 100mm 5 125mm or 6 150mm it would depend what size ducting you have installed. Please come back to me if I can help any furtherKind RegardsAnita
Can you provide all dimensions including screw hole distances for cowelled vent suitable for 150mm diameter duct
-
QCan you provide all dimensions including screw hole distances for cowelled vent suitable for 150mm diameter ductanswer nowA Hello AlanThank you for your question. The dimensions for the grille are 200mm square from the edge of the plate to the bottom of the hood is 138mm and the hole distance is 140mm. You can see the dimensions for this item under the brown grille on our website. If I can help any further please do not hesitate to contact meKind RegardsAnita
how is it fixed to the wall
-
A Hello EdwardThank you for your question. The front of the grille comes off and there are four holes for you to screw to the wall.Kind RegardsAnita
Hi there,
Can you please give me the outer dimensions of this grill and also the hole dimensions.
Thanks,
J.
-
QHi there, Can you please give me the outer dimensions of this grill and also the hole dimensions. Thanks, J.answer nowA Hello JasonThank you for your question. I will send you the dimensions on a separate e-mailKind RegardsAnita
what is the outside overall dimensions? am looking for 200x200 with a 150 spigot
-
A Hello StewartThank you for your questions. I will send that data sheet over on a separate e-mail.Kind RegardsAnita
I cannot find this product (150mm) spigot in Brown anywhere even though shown in product video. Is it still available?
-
QI cannot find this product (150mm) spigot in Brown anywhere even though shown in product video. Is it still available?answer nowA HI Tim thank you for your question i will give you a call today on this kind regards Phil
Hi, can you explain how the cowl is fitted to the wall and give the pitch of the screw holes please?
Regards,
Bill
-
QHi, can you explain how the cowl is fitted to the wall and give the pitch of the screw holes please? Regards, Billanswer nowA Hello BillThank you for your question. The dimensions for this product can be found under the product code QS238 in the gallery, there is also a video showing how to install this product. If I can help any further please do not hesitate to contact meKind RegradsAnita
What are the internal and external dimensions of the spigot
-
A Hello David, the cowls spigot is 150mm.the spigot is designed to fit inside a 150mm bit of pipeThe pipe diameter would beDiameter - Inner: 150mmDiameter - Outer: 153.60mmif you have any further questions please let us know.
I need 150mm x150mm outside dimensions with a 100mm dia spigot does this match my requirments?
-
QI need 150mm x150mm outside dimensions with a 100mm dia spigot does this match my requirments?answer nowA Hello JohnThank you for your question. All of the 100mm grille measurements are 155mm x 155mm this is the closes to your requirements. If I can help any further please do not hesitate to contact meKind RegardsAnita
Hi, my bathroom extractor is fitted to a Screwfix vent - Manrose Cowl Vent Brown 100 x 100mm (14789) - but as its NE facing it is still subject to rattling in the wind and is not doing what I want it to. Will your product minimise the wind noise? I prefer black as the colour.
-
QHi, my bathroom extractor is fitted to a Screwfix vent - Manrose Cowl Vent Brown 100 x 100mm (14789) - but as its NE facing it is still subject to rattling in the wind and is not doing what I want it to. Will your product minimise the wind noise? I prefer black as the colour.answer nowA Hello IanThe Manrose cowl you indicate appears to have a gravity flap inside the same as the DOM44902BK therefore there is unlikely to be much change in prevailing wind. It is possible the flap is too light and attaching some small section of draught excluder to the inside bottom of the flap may reduce the noise.
Are they suitable for a vent in a room with a gas fire.
-
A Hello SueThank you for your question. Unfortunately this product is not suitable for what you require. Please have a look at product codes QS2581 & QS2847 these items may be better for your application. If I can help any further please do not hesitate to contact meKind RegardsAnita
We have an outlet with a gravity flap and when the wind blows from a certain direction it drives us mad banging all day and night. Would the damper prevent this and how is it dampened?
-
QWe have an outlet with a gravity flap and when the wind blows from a certain direction it drives us mad banging all day and night. Would the damper prevent this and how is it dampened?answer nowA Hello MikeThank you for your question. Yes this product will stop the blow back of air. The damper is under the cowl and will close when the fan is not in use. If I can help any further please do not hesitate to contact meKind RegardsAnita
I have received this product the sides are con caved and the inner disc is stuck
It doesnt seem to be correct ?
Please advise
-
QI have received this product the sides are con caved and the inner disc is stuck It doesnt seem to be correct ? Please adviseanswer nowA Thank you for your enquiry, Please take a look at the video via the video button on the product pageor alternatively it can be viewed here on YouTubehttps://www.youtube.com/watch?v=UwYjzLIAeNo It will help to explain why the product is in the condition you received it in, this is to allow for installation
is this product suitable for gas hops
-
A Hello JohnThank you for your question. If your application is for a domestic cooker hood then yes this product will do your application as it is installed on the outside. If your application is commercial then i would recommend the circular weather lourve the product code for this item is QS3591If i can help any further please do not hesitate to contact meKind RegardsAnita
Hi,
Can you confirm that my order is for a 4 unit?
Regards John Ridge
-
A Hello JohnThank you for your inquiry. Yes the connection on this item is 4 100mmKind RegardsAnita
Hi, the product description of this black version calls this a cowled grille but the video is of a cowled product with a damper inside it and there is no grill that I can see? Is there a grill? I am looking for an outlet for my 150mm ducting from an extractor fan and I want to minimise noise. Thank you. Philip
-
QHi, the product description of this black version calls this a cowled grille but the video is of a cowled product with a damper inside it and there is no grill that I can see? Is there a grill? I am looking for an outlet for my 150mm ducting from an extractor fan and I want to minimise noise. Thank you. Philipanswer nowA Hello PhilipThank you for your question. This item is a cowled grille with a damper inside this will open when the extractor is in use and will close to stop the draft blowing back though the duct. If I can help any further please do not hesitate to contact me on 0208 463 9683Kind RegardsAnita
Would this product help reduce sound from a vent? If not, can you recommend any other product that can reduce noise from my neighbours kitchen extractor fan? Thanks.
-
QWould this product help reduce sound from a vent? If not, can you recommend any other product that can reduce noise from my neighbours kitchen extractor fan? Thanks.answer nowA Hi AlisonIn order to clarify the question, are you saying that you can hear your neighbours extractor fan through your own vent?
My kitchen extractor fan has a 200mmx200mm external grille on the outside of the wall which has 4 gravity flaps which rattle in the wind.
Is there a cowled outlet grille the right size I can replace it with?
Many thanks.
-
QMy kitchen extractor fan has a 200mmx200mm external grille on the outside of the wall which has 4 gravity flaps which rattle in the wind. Is there a cowled outlet grille the right size I can replace it with? Many thanks.answer nowA Hello MikeThis really depends on the diameter of the hole behind the grille?The dimensions of the square back plate for the Cowled wall outlets (plastic and metal) are 180 x 180mm with 150mm round spigot for the fan duct.If the hole for your fan is 150 diameter then there should be ample fixing for the standard cowled wall outlet.
Hi.
What plastic duct should I use to feed to this from the extractor fan ?
-
A Hello Joshua, The male spigot on this 100mm Domus Cowled Grille will fit inside our Kair System 100 Round Duct Pipe. The pipe is available in three lengths, so I would suggest selecting the most appropriate length for your cavity wall and duct run. Please see below for the hyperlinks to these products.350mm Length1 Metre Length2 Metre LengthKind regards, Michael
-
- 1
- 2
-
Garrett Finnerty (verified owner) –
Good product as per my expectations
Michael Hembry (verified owner) –
OK product
Howard Baker (verified owner) –
good solid unit better than many DIY ones
Feroze Nisar (verified owner) –
The flip cover stucks inside and does not open. I manually had to keep that cover permanently open for the air to go through. It would be fine if better material was used. I purchased two but going to throw both of these as there is no point of returning due to same amount of postage as their own value.
Peter Gower (verified owner) –
Excatly what I wanted, delivered in double quick time… excellent.
Ralph Turner (verified owner) –
The cowl had sides that were bent in obstructing the flap from opening and closing. A few minutes with a hot air gun (gently!) to straighten out the sides and all works as intended.It is a bargain price so ………..
David Watson (verified owner) –
The item came quickly by post and well wrapped. It is as described and perfect for the job in hand.
Andreas Charalambous Charalambous (verified owner) –
All good, speedy service, would use site again
Malcolm Humphreys (verified owner) –
Just what I needed coupled with spot on service.
Jason Tyszko (verified owner) –
Great product
Max Varnom (verified owner) –
works fine
Max Varnom (verified owner) –
works fine
Richard Thomas (verified owner) –
Good quality, great price, fast delivery!
Paul Hodgson (verified owner) –
all as described a little flimsy but at this price probs as good as you can expect very prompt thanks
Justin Finn (verified owner) –
Delivered Really quickly and great value for money
Pamela Craft (verified owner) –
Exactly as described
simon wright (verified owner) –
used this as a vent for the tumble dryer it works great thanks
Robert Walker (verified owner) –
Item does what it says on the tin at a very good price.
terence sowerby (verified owner) –
Great price, looks good and does the trick
nigel collingswood (verified owner) –
Item arrived very speedily and in perfect condition. Would recommend this site.
Barbara Colaco (verified owner) –
Sturdy plastic construction. Useful integral flap to prevent back draughts.
Barbara Colaco (verified owner) –
Sturdy plastic construction. Useful integral flap to prevent back draughts.