An extremely cost-effective heat recovery ventilation unit specifically designed for single rooms, small apartments, flats or houses. It is also ideal for retrofitting into houses as a damp and condensation solution.
The unit is a single room (dual with short duct runs) heat recovery unit with controllable air exchange for creating the best heat comfort in your home. This unit is controlled by an external speed switch to control the units three fan speeds.
A highly efficient, affordable heat recovery ventilation unit. It delivers filtered, fresh air into your home, and extracts stale, moist and dirty air with minimal heat loss.
Installation examples:
- Extract and supply air from a single room
- Extract air from 1 kitchen and 1 wet room (bathroom, toilet, shower room) and deliver fresh air to 2 living/sleeping rooms (short duct runs).
- Extract air from 2 wet rooms (bathroom + en-suite) and deliver fresh air to 2 bedrooms (short duct runs).
Low Profile
Due to its low profile, only 224mm deep it is perfect for mounting in small lofts, void spaces and suspended ceilings.
Heat Recovery
Maximum heat recovery is achieved with two centrifugal fans moving up to 105 m3/hour (29 l/s) of air and recovering up to 76% of heat with a cross-flow heat recovery core that is normally extracted to outside and waisted. The heat recovery ventilator also very quiet, manufactured from a double skinned acoustically lined box with a removable acoustic lid.
Easy Mounting
Designed for suspended installation. Built-in mounting brackets for easy mounting to roof purlins, ceiling joists and suspension structures.
Ducting
Compatible with 125mm ducting. Ducting through void/unheated areas should be thermally protected.
Rigid ducting should be used in preference to flexible ducting.
Filters
Two G4 filters are included with bottom access for easy and quick maintenance. Condensation control is via a base mounted condensation drain.
Comes with controller
A pre-wired speed controller is provided to control trickle, boost and purge heat recovery modes (speed 1, 2 & 3) to meet part F of the Building Regulations:
NB: Please note that due to the current worldwide component shortages, the version you receive may have a different brand name than shown here.
Heat Recovery Efficiency (Up to - %) | 65-76 |
Product Category | Heat Recovery Unit |
Round System (mm) | 125 |
Product Type | Heat Recovery - Modular |
Product Group | Ventilation Fan |
Spigot size (mm) | 125 |
Voltage (V) | 220-240 |
IP Rating | IPX4 |
Phase | 1 Phase 220/250 50/60Hz |
Power Min (Watts) | 30 |
Power Max (Watts) | 56 |
Decibel Rating (dB) - Low | 24 |
Decibel Rating (dB) - Max | 41 |
Weight (Kg) | 13 |
Packaged Weight (Kg) | 14.1 |
Packaged Length (mm) | 460 |
Packaged Width (mm) | 260 |
Packaged Height (mm) | 630 |
Pallet quantity | 16 |
Barcode | 5060272547752 |
Barcode - Type | EAN |
Manufacturer Product Code | KTM125 |
Airflow Performance (l/s) - Low | 16 |
Airflow Performance (l/s) - Med | 22 |
Airflow Performance (l/s) - High | 29 |
Airflow Performance (m³/h) - Low | 57 |
Airflow Performance (m³/h) - Med | 78 |
Airflow Performance (m³/h) - High | 106 |
Warranty (Years) | 2 |
Quick Search: | QS53282 |
Your question will be sent to a member of our team. We'll email you the answer and post it on this page. If your question is about an order you already placed, please use our Contact Form to reach the customer service team.
would this unit be suitable for 2 bed bungalow of 65 sq mtr; using kitchen & bathroom for inlet & 2 bedroom plus lounge as outlet. thanks Ted
Hello Ted
Hi I have a pottery shop where i currently vent the exhaust from the two electric kilns to the outside would it be possible to pipe the exhaust from these kilns through the unit so as to recover the heat that has gone into heating the kilns to there temperature for firing asking as with the cost of living we are looking to reuse this heat source as we have to fire the kilns but waste the heat that is generated
Good afternoon Peter and thanks for your question.
I'm looking to install an extract for an upstairs bathroom in a small 3 bed terrace. The bathroom has some damp issues and there is no space for a through the wall HR unit. 1. Is this unit suitable/ best unit for this use? 2. can I put the supply valve on the landing next to the bathroom and the extract in the bathroom to better distibute the air or should they both be in the bathroom? Thanks.
Good morning Alex and thanks for your question.
can this unit be wall mounted or is it ceiling mounted
Good morning Christopher.
Hi I am looking to install in the loft and extract from one downstairs shower room (thro airing cupboard) and one upstairs bathroom, with a view to putting fresh air into 2 bedrooms. Is this suitable? Answering this prompts other questions but one at a time... Thank you
Hi Rod. No this unit will not do that as the unit is really a single room unit.
|
Customers who bought this product also purchased |